In the first part of this series on paper miniatures I went over the various ways to get the paper miniatures with links to some kick ass guys on drivethrurpg as well as some links to a few custom tutorials. Today I want to continue this series with a short discussion on bases and the pros and cons of each type.
The easiest way to base the paper miniature is to grab a piece of foam core, put a slot in it and insert your figure. It may require a coin or similar on the bottom to give it a little heft. These are cheap, plentiful and with a little work, can look good. This isn't the method I use, but Wyloch goes over it in his video on creating the paper miniature.
The next option is also a DIY option with the caveat that it requires you to have access to a 3d printer. 3d printers can be fairly expensive, especially a genuine Prusa, however there are several models of inexpensive printer that are good for basic printing for a gamer.
I have an A-net A8 which is a decent machine, print quality wise, and gives you the ability to try getting your feet wet for not a lot of money. It is built with cheaper components which should be replaced if you are going to use it a lot though. It will be more than able to print up bases and other things that you might find at a website like thingiverse. These two links are some samples of thingiverse links you can use for basing paper miniatures. Sample 1 Sample 2
Moving away from the DIY option we start to move into some for of clip. The first and cheapest version of these is a binder clip. These are a pretty good solution being easily available, inexpensive and coming in multiple sizes and colors. I don't personally use them, and right now as I am typing this I am wondering why. The only real drawback I can see to these is they will be a little more fiddly when it comes to changing your figures over. You will have to re-insert the metal handles so you can easily open the clip to remove the figure. I think the pros may outweigh the cons here.
You can get a cheap acrylic base designed for boardgames as well. These are pretty good and give you a clear plastic base, and can be purchased in multiple colors. The downside to these is they require a fairly thick card as the clip is fairly wide. I have used these and need to use several layers of construction paper to make them work. Despite how inexpensive they are, I don't really recommend these ones unless your paper figs are quite thick.
The ones I have purchased and use the most are most similar to the binder clips, they can be found sold as "card holders". These are easy to use and replace the figure into. I have only found them in black, which is another strike against this style. The downside to these is they are among the more expensive option, that being said they are still going to run you less than $.50CAD cents each. As much as I like a lot about this style, I doubt I'll be buying more of them.
Litko makes a range of bases for paper figures, similar to the 3d printed model I talk about, these are square or circular and come with a curved slot to hold your figure. The downside to these are two fold. One, they are getting upwards in price, running about $.50CAD each. Two, I don't find litko to have especially friendly shipping options to Canada. If you are in the USA this might be a great option where they will be about $.40USD each and have better shipping options.
Over the past year of using paper miniatures in most of my games I have used several of the above purchaseable solutions. At this time I have not tried the binder clips or 3d printed models, but I think that the binder clips might be the best option being inexpensive, easy to get and in multiple colors. I have also not ordered from Litko. Another possible downside to some of these is that they represent non-standard bases sizes. I don't think it'll take much to make them work, but it's something to think about.
Now that we have our bases and figures, next week we will talk about the process I go through when I assemble these figures! Until next time, keep it weird out there!
'Barbarism is the natural state of mankind,' the borderer said, still staring somberly at the Cimmerian. 'Civilization is unnatural. It is a whim of circumstance. And barbarism must always ultimately triumph.'
-Robert E. Howard
Beyond The Black River
Places of Interest
Showing posts with label miniatures. Show all posts
Showing posts with label miniatures. Show all posts
Thursday, April 12, 2018
Wednesday, April 4, 2018
Printable Miniatures. Part 1, Getting the Image.
In Part 2 we talk about basing options!
We all love miniatures, or at least I suspect you do if you are reading my blog. If you play a system that uses a lot of smaller level fodder type characters, such as a 2d20 system or Savage Worlds, you might find it hard to have 15 or 20 of a single figure type. Even for me, with the Conan board game to pull from, it can be hard to have enough bad guys.
Enter the paper miniature, sometimes refered to as flats. I first came across these when I was getting back into gaming and watching the various channels on youtube that exist. Check out Wyloch's tutorial on how to make your own. He goes through how to make these props, step by step using images found images. Please be respectful of copyright when you are building printable minis this way.
We also have Printable Heros over on Pateron. For a couple of bucks you can get access to the cool collection of figures he has produced. For me though, I often need something fairly specific and I am building them pretty close to the last minute. I don't have time to search the net for the image and cut and paste it, trim it up, size it and get it ready for play. Sometimes I just want to do a quick search, print out the figure and get it on my table. For this I go to DriveThruRPG.
I am sure you are all aware of DriveThruRPG. If you are not click the above link and it will take you to a wonderland of digital products, BUT back to printable miniatures.
There is a wealth of people creating these printable heros and monsters! Part 2 of the series will talk about the supplies I use to make mine, as well as some alternatives. Once we have all of our supplies together we will see about putting together some of these creations!
Until then, keep it weird!
The above post contains affiliate links, using them will give this blog a small commission on the sale.
We all love miniatures, or at least I suspect you do if you are reading my blog. If you play a system that uses a lot of smaller level fodder type characters, such as a 2d20 system or Savage Worlds, you might find it hard to have 15 or 20 of a single figure type. Even for me, with the Conan board game to pull from, it can be hard to have enough bad guys.
Custom Minis from a Ghoul stock image I got from DriveThruRPG |
We also have Printable Heros over on Pateron. For a couple of bucks you can get access to the cool collection of figures he has produced. For me though, I often need something fairly specific and I am building them pretty close to the last minute. I don't have time to search the net for the image and cut and paste it, trim it up, size it and get it ready for play. Sometimes I just want to do a quick search, print out the figure and get it on my table. For this I go to DriveThruRPG.
I am sure you are all aware of DriveThruRPG. If you are not click the above link and it will take you to a wonderland of digital products, BUT back to printable miniatures.
These guys are probably my favorite shop creating printable miniatures. They are have a wonderful distinct style and he has a wide variety to fill many many different gaming roles! Get them here! | |
Another store that has an excellent selection of figures for use with your games. Like Okum arts there is a wide variety of figures from fantasy to sci-fi. Get them here! | |
The ICRPG Core set is more expensive but comes with a wealth of content, including a selection of printable miniatures for your table in Hankerin's distinctive black and white style. Get it here! | |
These guys have a wide selection of printable miniatures(some are even free!) as well as papercraft buildings. Get them here! | |
A later entry to this list, as I just found them recently is Trash Mob Minis. Like Okum Arts above these guys have an impressive collection of paper figs in a very distinctive style. I recommend checking them out! |
There is a wealth of people creating these printable heros and monsters! Part 2 of the series will talk about the supplies I use to make mine, as well as some alternatives. Once we have all of our supplies together we will see about putting together some of these creations!
Until then, keep it weird!
The above post contains affiliate links, using them will give this blog a small commission on the sale.
Labels:
25/28mm,
2d20,
2d20 lite,
CONAN,
Conan 2d20,
DND,
Fantasy,
miniatures,
RPG,
Sci-fi
Tuesday, February 13, 2018
Miniature Scale Comparisons.
"How well do they scale?"
When people talk about miniatures from board games(BG) this is one of the first things that comes up. It is probably second only to people wondering how good they are.
Scale is a common concern among miniature gamers, and it gets asked about different figures from different companies all the time, it is not just asked about BGs.
I recently got my pledge for "Mythic Battles: Pantheon" and let me say, that I love these figures. I was asked almost immediately about how well they scaled with Conan. This blog post will attempt to compare and contrast a fairly decent range of figures including Bones, Bronze Age, Conan, Mythic, Wizkids pre-paints and the new line of unpainted figures from Wizkids.
One last caveat. We are not scale modelers in my opinion. We use our miniatures and our terrain to make our battles or rpgs come alive with cool ideas. The figures and terrain we use are seeds to our imagination and serve to keep each of us playing more or less in the same frame.
The last Mythic figure I simply included for fun as it is the "god" scale for the game.
These two images show a Bones Conan-eque figure next to some Bronze Age figures, both are your pro-typical barbarian figs. I think they are pretty similar in scale, with the Bronze Age figs perhaps being more physically proportional. Either way they will work fine together on the table.
The two males next to each other show the proportional differences much clearer. Despite these I still think they will work fine on the table together.
Here we have that same Bones figure next to one of the pre-paint figures. I think she is from the "Rise of the Runelords" collection, but I can't recall for sure. Again the scale is pretty good. She stands at a human height next to our hulking barbarian. He might even look a little short if their bases were the same height. But again I have no issues using these two figures together on the table.
This is a scale comparison between one of the Conan BG figures and our Conan-eque Bones figure again. Again we see more of the same. Decent scale, easily useable on the same table, even thought the Conan BG figure is a little talled.
Same scale we saw in the Conan BG figure, this Mythic BG figure is slightly taller than this Bones figure, but still useable together on the same table. I would also like to take this time to point out the excellent detail on the Mythic figure.
Now lets look at a few non-Bones comparisons. We have seen these two before, Conan BG vs Bronze Age. I think they stack up pretty well together. If I had to make a critical note on the scale differences, the Conan BG fig makes the Bronze age fig look like he has a giant head. From a tabletop perspective though, I think they will be great together.
Comparing one of the new Deep Cuts figures (or Nolzurs I can't actually remember which) to the Bronze Age figure. I think these two are a pretty good fit. She is smaller, but generally in fantasy (and other generally heroic and idealized) art women are drawn with smaller frames.
Not surprisingly the Conan BG and Mythic BG figures both scale very well together. Probably the most similar sized strong dude to strong dude of the lot.
To be complete here is the Bronze Age figure next to the Mythic BG figure. Nothing new here, pretty much what we saw when comparing the Bronze Age to the Conan BG figure.
One final shot of a Bones, Mythic God and Mythic Warrior....
This Bones Paladin is in a pretty similar stance as the Mythic Warrior, and has a base of about the same height. He stands nearly a head shorter. This is getting to the point where they might start to look funny in my opinion, but then again, maybe the Paladin is just a short human or an elf?
Are you more of a scale perfectionist than I am? Do some of these figures not work for you when placed together? Why not let me know what you thin and drop me a comment below?
When people talk about miniatures from board games(BG) this is one of the first things that comes up. It is probably second only to people wondering how good they are.
Scale is a common concern among miniature gamers, and it gets asked about different figures from different companies all the time, it is not just asked about BGs.
I recently got my pledge for "Mythic Battles: Pantheon" and let me say, that I love these figures. I was asked almost immediately about how well they scaled with Conan. This blog post will attempt to compare and contrast a fairly decent range of figures including Bones, Bronze Age, Conan, Mythic, Wizkids pre-paints and the new line of unpainted figures from Wizkids.
One last caveat. We are not scale modelers in my opinion. We use our miniatures and our terrain to make our battles or rpgs come alive with cool ideas. The figures and terrain we use are seeds to our imagination and serve to keep each of us playing more or less in the same frame.
Starting with a group shot of all the figures. Bronze Age, Bronze Age, Pre-paint, Bones, Bones, Bones, Deepcuts, Conan, Conan, Mythic, Mythic. |
The last Mythic figure I simply included for fun as it is the "god" scale for the game.
These two images show a Bones Conan-eque figure next to some Bronze Age figures, both are your pro-typical barbarian figs. I think they are pretty similar in scale, with the Bronze Age figs perhaps being more physically proportional. Either way they will work fine together on the table.
The two males next to each other show the proportional differences much clearer. Despite these I still think they will work fine on the table together.
Here we have that same Bones figure next to one of the pre-paint figures. I think she is from the "Rise of the Runelords" collection, but I can't recall for sure. Again the scale is pretty good. She stands at a human height next to our hulking barbarian. He might even look a little short if their bases were the same height. But again I have no issues using these two figures together on the table.
This is a scale comparison between one of the Conan BG figures and our Conan-eque Bones figure again. Again we see more of the same. Decent scale, easily useable on the same table, even thought the Conan BG figure is a little talled.
Same scale we saw in the Conan BG figure, this Mythic BG figure is slightly taller than this Bones figure, but still useable together on the same table. I would also like to take this time to point out the excellent detail on the Mythic figure.
Now lets look at a few non-Bones comparisons. We have seen these two before, Conan BG vs Bronze Age. I think they stack up pretty well together. If I had to make a critical note on the scale differences, the Conan BG fig makes the Bronze age fig look like he has a giant head. From a tabletop perspective though, I think they will be great together.
Comparing one of the new Deep Cuts figures (or Nolzurs I can't actually remember which) to the Bronze Age figure. I think these two are a pretty good fit. She is smaller, but generally in fantasy (and other generally heroic and idealized) art women are drawn with smaller frames.
Not surprisingly the Conan BG and Mythic BG figures both scale very well together. Probably the most similar sized strong dude to strong dude of the lot.
To be complete here is the Bronze Age figure next to the Mythic BG figure. Nothing new here, pretty much what we saw when comparing the Bronze Age to the Conan BG figure.
One final shot of a Bones, Mythic God and Mythic Warrior....
This Bones Paladin is in a pretty similar stance as the Mythic Warrior, and has a base of about the same height. He stands nearly a head shorter. This is getting to the point where they might start to look funny in my opinion, but then again, maybe the Paladin is just a short human or an elf?
Are you more of a scale perfectionist than I am? Do some of these figures not work for you when placed together? Why not let me know what you thin and drop me a comment below?
Monday, February 5, 2018
New video up!
I finally managed to get the first half of a craft video up this weekend!
Hope everyone enjoys it, tried a bunch of new ideas with this one.
Hope everyone enjoys it, tried a bunch of new ideas with this one.
Thursday, October 5, 2017
Pillar of Skulls!
New terrain project up on the YouTube channel. This week we are building a marble pillar adorned with 4 skulls and chains. It is a cool craft and great addition to any dungeon! Check it out!
Thursday, September 21, 2017
Episode 41: Portals of Doom!
New video on the youtube channel on building wall sections with removable panels. I hope you find it useful!
Thursday, August 10, 2017
3d Printing useful or not?
Awhile ago I picked up a 3d printer from Gearbest. It was the Anet A8, an inexpensive/cheap acrylic frame printer below $300cad. It is a basic FDM model, a clone of the Prusa system.
I have printed in ABS and PLA, and frankly I have gotten nicer prints with the ABS, but it is trickier to work with and has nastier fumes, so I am now working largely with PLA.
My latest video is an overview of printing miniatures (I needed 8) for a scenario using statues/golems.
For me the answer to the question, is that it is useful, though not a replacement to regular modeling and miniatures.
Have a watch and don't forget to leave a comment.
I have printed in ABS and PLA, and frankly I have gotten nicer prints with the ABS, but it is trickier to work with and has nastier fumes, so I am now working largely with PLA.
My latest video is an overview of printing miniatures (I needed 8) for a scenario using statues/golems.
For me the answer to the question, is that it is useful, though not a replacement to regular modeling and miniatures.
Have a watch and don't forget to leave a comment.
Tuesday, August 8, 2017
The Unknown Isle: Skull peak.
With my next session only a few days away I needed to put together the central piece for what will either be the climax of the evening, or very close to it. I have known what I wanted from the beginning of this part of the campaign.
The players are essentially shipwrecked on a mysterious island. There are hints of magic, there is a giant stockade, a small tribe of natives, an ancient city, apes and of course dinosaurs. On the peak of this island rests a skull cavern.
I had initially sought to carve this from foam and got a decent way into the rough cut of that carving, then I was in Michaels, and being as Halloween is the next major holiday I got a foam skull for about $5cad. It's scale was close to what I was building and would allow me to just short cut around the caving of the skull I was working on.
I didn't have time to film the construction, but I thought I could take a few photos and build a blog post around it. I hope you all enjoy it and find it useful.
And ON TO THE BUILD!
You will need......
Tools
Razor knife or hot wire cutter.
Hot glue gun.
paint brushes.
Materials
A foam skull.
XPS or similar.
Tinfoil.Papertowel.
PVA glue.
The Skull in question. Foam, ~$5cad at Michaels.
|
Take the XPS, trace the skull foot print and cut it out. Bevel the edges and make a cut inwards for the cave. |
The skull sitting on it's rocky base. |
Using some scrap foam, cut out to boulder shapes. |
The front of the skull cave. |
Using tinfoil build up around the skull. Glue it with hot glue. |
Test fit the skull and make sure you are happy. I could have used more tinfoil, but it worked out. |
Using some paper towel, water and PVA I applied some body to the piece. Generally, wet the paper towel, place where you want and brush watered down PVA over it. |
After it had dried I added some more shape with tinfoil to make it more rocky.
|
The other side of the skull. |
Add more towel and glue over the new foil armature.
The more of this you add the stronger it will be, but the longer it will take to dry. |
Once the towel and glue is dry, give it a nice black base coat. Mod Podge and black paint. |
Next base the whole thing in whatever color of stone you want. I used a dark brown here. |
Add fake greenery liberally, yet sparsely over the skull. I also glued in a couple of plastic crystal gems I got at the dollar store. |
And the skull peak in place on a rocky plateau ready for some adventurers to come and seek it's mysteries. |
This was a fairly quick craft. I managed to build it over a course of a week spending a few minutes here and there on it. It adds quite a lot of character to the scenario and a dramatic center piece for your game.
I hope you enjoyed the idea and found it useful. Feel free to browse the blog for other ideas, or leave a comment below with your thoughts on this project.
And of course come check out the You Tube channel over at https://www.youtube.com/channel/UCvCRyMzJoQBnjb-Qq5Rng_Q
Keith
Thursday, August 3, 2017
Episode 34: The Rope Bridge.
The rope bridge is a classic in adventure scenes. It even has it's own entry on tvtropes.org, have a look, http://tvtropes.org/pmwiki/pmwiki.php/Main/RopeBridge
Do you have one or two built for your D&D, Pathfinder or other RPGs? If not you have come to the right place. I am going to show you how to build a pretty simple bridge from basic materials: a bamboo matt, some XPS Styrofoam, chipboard and glue.
You can build it exactly like I did, or you can use this as inspiration and go your own way. The sky is the limit, or maybe the depth of the chasm is limited only by your imagination.
The video is available now on my YouTube channel, so swing by and have a watch!
Do you have one or two built for your D&D, Pathfinder or other RPGs? If not you have come to the right place. I am going to show you how to build a pretty simple bridge from basic materials: a bamboo matt, some XPS Styrofoam, chipboard and glue.
You can build it exactly like I did, or you can use this as inspiration and go your own way. The sky is the limit, or maybe the depth of the chasm is limited only by your imagination.
The video is available now on my YouTube channel, so swing by and have a watch!
Thursday, July 27, 2017
The Black Coast: Mitra's Justice
As the Conan RPG rules become solidified for Modiphius I look toward the start of a campaign. I have always enjoyed the tales of the Black Coast and the Black Kingdoms and have decided to start my players in those humid and mysterious realms.
First we need to get them there. I have taken a look at a few videos on this matter, and really need to blame Black Magic Craft for his ship, it made me want one.
As I have worked on this things have changed here and there. I had no real plans going forward with this.
For sailing the rough oceans and trade routes of Argos I decided I wanted something a little bit more substantial, and so I give you a build for the mighty ship, "Mitra's Justice".
This ship will probably be a stand in for a lot of ships of size for the campaign, and I do plan on building a smaller one as well, more like what BMC created to work as a pirate vessel.
In the end I suspect I would do some things different, especially when it comes to the wood planking, but overall it is a very cool piece to have used in the campaign and once I get another ship complete it will allow for some extra cool miniature based scenarios.
I hope you all enjoy the build!
First we need to get them there. I have taken a look at a few videos on this matter, and really need to blame Black Magic Craft for his ship, it made me want one.
As I have worked on this things have changed here and there. I had no real plans going forward with this.
For sailing the rough oceans and trade routes of Argos I decided I wanted something a little bit more substantial, and so I give you a build for the mighty ship, "Mitra's Justice".
This ship will probably be a stand in for a lot of ships of size for the campaign, and I do plan on building a smaller one as well, more like what BMC created to work as a pirate vessel.
In the end I suspect I would do some things different, especially when it comes to the wood planking, but overall it is a very cool piece to have used in the campaign and once I get another ship complete it will allow for some extra cool miniature based scenarios.
I hope you all enjoy the build!
This is 1/2" blue Styrofoam. It measures about 19" long and 5.5" wide. The figure is a Reaper Bones Miniature. This will form the basis for the ship. |
Next I cut out the quarter deck and the forecastle deck. The quarterdeck is doubled to give it a little more height. |
Next, working with foam core, I began work on the sides by first measuring 1/2 the total hull length with a long sheet of paper and then transferring it, as well as the deck measurements. |
Once these measurements were transferred I cut them out to create the two sides of the hull. |
Peeling the paper from the outer side of the foamcore first I then used a sharp knife to score the foam core so it would flex around the blue foam. |
This was done at the front and back of the ship. |
Next, using white glue I started gluing the main ship decks together. |
Once the decks were together, I glued the hulls to the deck using more white glue with pins to hold everything in place. |
I decided to change the boat up and add some fortifications to it. |
Adding the back structure for the fortifications. |
Foam core cut to make the base of the walls. |
Everything dry fit. |
Items are glued with white glue. |
Cut cardstock into 1cm wide strips and hot glued to the hull. |
Ship planking coming along. |
Cutting boards for the fortifications and adding texture. |
Ship wall planks ready to go. |
Foam extension glued onto the hull and keel. This will also give us the advantage of having a stronger keel. |
Adding wood planks around the cabin extension. I will probably add some windows around the cabin as well. |
I was unsure how I wanted to texture the decking. I decided on individual planks. Main deck |
Forward deck planked. |
Working on the rear deck. |
Rear deck finished, now to work on the remaining exposed foam. |
Back deck more or less completed. Will still need a ships wheel. |
Closing up the front. Used regular and skinny popsicle sticks to add a stepping system to allow everything to match. |
Cutting matching grooves into the deck hatch so it can still attach. |
Main deck hatch glued into place. |
Remaining parts of the ship covered in wood. Temporary door placed for photo. |
Cut and texture two identical popsicle sticks long enough to reach from the main deck to the top of the quarter deck. Also cut out 5 or so bamboo skewers approximately wide enough to allow a miniature to climb the ladder. Evenly mark spots you want to glue the rungs. |
Glue the rungs in place with hot glue. |
Add a dab of hot glue to the tops of the rungs and attach second stick, make sure the bottoms are even so the ladder will stand. |
Attach, or don't, the ladder to the main deck and quarter deck of the ship. |
Beginning to paint it all with a black base coat. |
Was still missing something. Quick look at some reference photos and I added this front piece to finish the look. Foam and carved wooden dowel. |
Finished the black base coat. |
Adding a dark brown over the base coat. |
Wooden planking of the ship. |
Dry brushed with a lighter brown and adding nail details with a sharpie. |
Mast. Washers encased in a craft stick box glued to a carved dowel. Cotton string added to the base of the mast. |
Ship all together in a mock scenario. Pirate miniatures from Monolith's CONAN board game. |
Subscribe to:
Posts (Atom)